Understanding Plumbing Basics for Bathtub Installation
Understanding Plumbing Basics for Bathtub Installation
Blog Article
We've uncovered this article pertaining to A Step-by-Step Guide to Installing a Bathtub down the page on the internet and concluded it made sense to share it with you over here.
Mounting a bath tub isn't precisely brain surgery, but it does require solid plumbing, woodworking, and also often, tiling skills. Changing an old bath tub with a brand-new one is likewise a reasonably challenging project. If the old tub is conveniently easily accessible, the job can relocate rapidly; if you need to open up a wall to eliminate the old tub and also place the brand-new tub, the job is a lot harder. In either case, the project is within a house handyman's abilities, although you will need an assistant to move out the old bathtub as well as set in the brand-new one. Ensure you have actually certified on your own for the task as well as are comfortable attempting it. Rather than working with a professional to take over a halfway-completed task, it is much better to take into consideration employing one prior to you start. Opportunities are you may need a specialist plumber to make tube connections.
This article will aid you install a new bath tub in your bathroom if you have already gotten a brand-new tub and also don't need to transform the plan of your previous water supply pipes.
Your devices and also material checklist need to consist of the following:
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your setup, after that the first thing you must do is separate the water supply. After doing so, activate the faucets to drain pipes any water staying in the system. The procedure of removing the existing taps can be fairly troublesome as a result of the restricted gain access to that is frequently the instance.
Use a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipes to the faucets. Have a towel ready for the staying water that will certainly originate from the pipes. Once the supply pipes have actually been removed, utilize the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single taps from transforming throughout this procedure. When the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any type of old securing substance.
Before proceeding to fit the brand-new faucets, compare the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the brand-new faucets to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic connector to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and the various other end supplies a connection to the existent supply pipes.
If you require to fit a monobloc, then you will certainly need lowering couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the faucet in the mounting hole in the bath/basin making certain that the washers remain in place in between the faucet and also the sink. Protect the tap in position with the maker supplied backnut. Once the tap is firmly in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with regular tap connectors. The former type ought to be attached to the tap finishes initially, tightening only by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Setting up the Tub
Using both wood boards under its feet, place the tub in the required setting. The wooden boards are valuable in uniformly spreading the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four tiny points.
The next goal is to ensure that the tub is leveled all round. This can be achieved by inspecting the spirit level and also adjusting the feet on the bathtub until the spirit level reads degree.
To mount faucets, fit all-time low of the furthest adaptable faucet adapter to the ideal supply pipe by making a compression sign up with; then do the same for the various other faucet.
Activate the water system as well as examine all joints as well as new pipework for leakages and also tighten them if necessary. Fill up the bath tub and additionally check the overflow electrical outlet and the regular outlet for leakages.
Lastly, take care of the bath paneling as defined in the producer's user's manual. Tiling and sealing around the bathtub needs to wait until the tub has actually been used at the very least when as this will certainly settle it right into its last position.
Getting ready for the Installation
To start with, the sustaining framework provided with the bath should be fitted (if needed) according to the maker's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is essential to make sure that if the faucet comes with a plastic washing machine, it is fitted between the bath and the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps system to stop pressure on the bath tub.
Fit the flexible tap adapters to the bottom of the two taps utilizing 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet through the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you utilize every one of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath ought to now be ready to be suited its final placement.
Tiling Around the Bath tub
In the area where the bath fulfills the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate enough to split a rigid seal, causing the water to pass through the wall surface between the bathroom and the tiling, causing difficulties with dampness and also feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to blend in your components and also fittings. They are marketed in tubes and also cartridges, and also can sealing voids approximately a size of 3mm (1/8 inch). If you have a larger space to fill, you can load it with spins of soaked newspaper or soft rope. Remember to constantly load the tub with water prior to sealing, to allow for the movement experienced when the bathtub is in usage. The sealer can split rather very early if you do not take into account this motion prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also quickly readily available on the market. It is advisable to fit the tiles using waterproof or water resistant glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was guided to that write-up on Installing A Bathtub from an associate on another website. Loved our piece? Please share it. Let another person locate it. Thanks a bunch for your time. Don't forget to check up our site back soon.
Protect plumbing integrity; connect now. Report this page